Our low-voltage complete electrical equipment is mainly used in industrial plants, commercial buildings, and residential communities for low-voltage distribution and power quality management. The range covers draw-out/fixed type low-voltage switchgear, capacitor compensation cabinets, active filter cabinets, comprehensive distribution cabinets, and various AC distribution boxes — covering the full scope from main distribution to end-point distribution.
We emphasize safety and intelligence; some products integrate digital fire-inspection functions for remote monitoring and fault warning. Manufacturing strictly follows standards such as GB/T7251, with customized configurations available based on load, circuit quantity, and installation environment.
Wenzhou Xubian Electric Co., Ltd. is a technology-driven China Low Voltage Switchgear Manufacturer and Custom Low Voltage Distribution Cabinet Supplier, specializing in the production, sales and after-sales maintenance of high- and low-voltage complete switchgear systems.
We have a dynamic and innovative team for R&D, design, management and marketing, backed by solid R&D and production competence.
Following our quality policy: “Survival through Quality, Development through Innovation, Continuous Improvement, Customer Satisfaction”, we enforce strict control over all production stages to ensure 100% qualified finished goods. Our workshop is well‑equipped with full‑range processing facilities, testing apparatus and advanced inspection solutions.
Wenzhou Xubian Electric Co., Ltd. is a China Low Voltage Switchgear Manufacturer supplying complete low voltage distribution and power quality equipment for industrial plants, commercial buildings and residential communities. Our range covers draw-out and fixed switchgear, capacitor compensation cabinets, active filter cabinets, comprehensive distribution cabinets and AC distribution boxes, from the main incoming board to the final lighting circuit. We manufacture to GB/T7251 and configure each assembly around load profile, circuit quantity, installation environment and the control interface required by the project.
We organize the range by duty rather than cabinet size alone. Main distribution and motor control assemblies carry the high-current paths; compensation and filtering cabinets correct power quality at the busbar; distribution boxes split final circuits at the point of use. This lets us supply a coordinated package with consistent busbar, protection and labeling conventions across the project.
| Product family | Models in our range | Where it fits | Configuration focus |
|---|---|---|---|
| Main LV distribution and motor control | XBXL, XBMNS, XBGCK, XBGCS, XBGGD | Incoming, bus-tie, feeder and MCC sections in plants, commercial buildings, hotels, airports and infrastructure | Rated current, breaker frame sizes, busbar short-time withstand, IP30/IP40, cable entry |
| Draw-out switchgear | XBMNS low voltage draw-out switchgear, XBGCK, XBGGD | Processes needing fast module replacement and safe isolation in three-phase five-wire 400/660 V systems | Drawer module size, mechanical interlock, PC/MCC mix, 5000 A busbar, 50–80 kA Icw |
| Reactive compensation | XBGGJ low voltage capacitor switchgear, XBJP | Main busbar power factor correction and combined distribution/compensation | Capacitor stages, switching devices, ventilation, metering and protection |
| Active harmonic filtering | APF active filter cabinet | Nonlinear loads such as rectifiers, drives, IT equipment, HVAC and welding systems | 50–450 A capacity, 3P3W/3P4W, CT ratio, parallel expansion, Modbus communication |
| End distribution | XBJXF, XBPZ30, XBXM | Final circuits in buildings and workshops; lighting, socket and small power distribution | Way count, enclosure size, IP rating, door and lock arrangement, circuit labeling |
| Fire-fighting patrol control | XBS-K, XBS-P | Fire pump standby integrity in commercial, industrial and residential buildings | PLC or intelligent controller, starting method, pump count, alarm interface, patrol cycle |
Industrial plants use the range for incoming substation distribution, motor control centers, capacitor correction and harmonic filtration where drives and rectifiers distort the supply. Commercial buildings and residential communities use main distribution cabinets, comprehensive compensation cabinets and final distribution boxes for tenant metering, lighting and small power. Airports, docks, hotels and broadcast centers require the same draw-out logic where circuits must be isolated and replaced without shutting down the section.
Draw-out construction is the right choice when maintenance access and circuit isolation dominate the operating plan. The XBMNS assembly uses a 25 mm C-section frame, standardized drawer modules and a mechanical interlock that prevents a drawer from being withdrawn under load. PC and MCC sections can be combined on a 200 mm module so incoming, bus-tie and motor feeders share one lineup without losing compartment discipline.
Construction details that affect service life
The APF active filter cabinet monitors load current through an external CT, extracts harmonic components in its DSP and injects an equal and opposite current through IGBT switching. It suits installations where the harmonic spectrum changes with production or occupancy and passive filters would be difficult to tune. For displacement power factor, XBGGJ capacitor switchgear and XBJP comprehensive cabinets provide staged correction at the main busbar, with switching and ventilation matched to the capacitor bank.
XBS-K and XBS-P cabinets use PLC or intelligent controller logic to cycle fire pumps at low speed and low frequency during standby. If a fire signal arrives during patrol, the patrol stops immediately and the pump enters fire-fighting operation according to the configured starting method.
Phase loss, phase failure, output overcurrent and short-circuit conditions raise alarms so the pump remains ready rather than seizing through inactivity.
The XBMNS draw-out assembly defines the upper end of our low voltage envelope. Its horizontal busbar is rated up to 5000 A, with a rated insulation voltage of 660/1000 V, a rated frequency of 50 or 60 Hz and a short-time withstand current of 50, 65 or 80 kA for 1 s. Peak withstand current is 105, 140 or 176 kA, and the enclosure is IP30 as standard with IP40 available by special note.
Protection and control are configured around the single-line diagram and the plant control philosophy. Incoming and bus-tie frames use the specified breaker series; feeders use molded-case or miniature circuit breakers with the required trip units; metering, CTs, surge protection and status signals are wired to terminal blocks for external SCADA or building management connection. The APF communicates over Modbus RTU on RS485 or RS232, and the XBS patrol cabinet uses PLC or intelligent controller logic with status signals to the fire alarm panel.
Quality control starts with incoming inspection of busbars, breakers, capacitors, filters and sheet-metal parts. In-process checks follow assembly and wiring; semi-finished assemblies are tested for insulation resistance, voltage withstand and DC resistance before they move forward. Finished cabinets receive voltage-withstand, temperature-rise and function tests, and test reports are issued before packing. For non-standard projects, prototypes are manufactured and tested for insulation, temperature rise and voltage withstand for customer approval before mass production.
Typical documentation package
Draw-out modules allow a circuit to be isolated and replaced without dismantling the busbar; fixed sections are accessed from the front for cable termination and breaker maintenance. APF cabinets include self-diagnosis and protection, and the XBS patrol controller raises alarms on phase, current and short-circuit faults. Spare parts remain available after the warranty period, and our after-sales team provides online troubleshooting in English.
Our proposal is based on the working point, material and production target. For low voltage assemblies, the working point is the single-line diagram and fault level; the material is the copper busbar, breaker selection, enclosure and cable interface; the production target is the delivery sequence and site installation plan.
We manufacture low voltage draw-out and fixed switchgear, capacitor compensation cabinets, APF active filter cabinets, comprehensive distribution and compensation cabinets, AC low voltage distribution cabinets, distribution boxes and fire-fighting patrol-inspection equipment. The range covers main incoming distribution, motor control, power factor correction, harmonic filtering and final circuit distribution.
Yes. We work from the single-line diagram, load schedule and installation conditions to configure busbar ratings, breaker frame sizes, drawer modules, cable entry, metering and labeling. OEM and ODM programs can include private-label panels, project-specific voltage and frequency, enclosure finish and drawing sets.
APF capacity is selected from the measured or expected harmonic spectrum, load current and target THDi, using 50–450 A modules with parallel expansion where needed. Capacitor cabinets are staged against the displacement power factor, switching devices, ventilation and permissible harmonic conditions at the busbar.
Assemblies go through incoming inspection, in-process checks and finished-product factory tests including voltage withstand, temperature rise and function verification. The documentation package includes drawings, factory test reports, operation and maintenance manuals, packing lists and export documents, with certification support for the target market.
Standard models are typically delivered in 7–15 working days. OEM and ODM products follow the drawing and production schedule confirmed in the proposal. Products carry a 12-month warranty for repair, replacement and return, with spare parts available after warranty.
We supply installation drawings, manuals and test reports before shipment, then provide online installation guidance and troubleshooting in English. For key-project equipment, on-site unpacking, installation and commissioning support can be arranged, with 24-hour online after-sales technical support.