XBMNS Low voltage draw out switchgear Custom

Home / Products / Low Voltage Complete Electrical Equipment / XBMNS Low voltage draw out switchgear
Wenzhou Xubian Electric Co., Ltd.
  • XBMNS Low voltage draw out switchgear
  • XBMNS Low voltage draw out switchgear
100022 Model Designation
XB Enterprise code
M Modular
N New type
S System
□ Main circuit scheme number
□ Auxiliary circuit scheme number

1. Ambient air temperature shall not exceed +40 ℃ and shall not be lower than -5 ℃, and the average temperature within 24 h shall not exceed +35 ℃.
2. The relative humidity of the ambient air shall not exceed 50% at a maximum temperature of +40 ℃. A higher relative humidity is permitted at lower temperatures, for example 90% at +20 ℃, but moderate condensation that may occasionally occur due to temperature changes shall be taken into account.
3. For indoor use, the altitude of the installation site shall not exceed 2000 m.
4. It shall be installed in places free from severe vibration and shock, and where electrical components are not subject to corrosion.

No. Item Header: GB7251.1-2005 Low-voltage Switchgear and Controlgear Assemblies (TTA)
IEC60439 “Low-voltage Switchgear and Controlgear Assemblies”
1 Overvoltage category IV III
2 Pollution degree 3
3 Rated operating voltage (Ue) (V) 400/660
4 Rated insulation voltage (Ui) (V) 660/1000
5 Rated frequency (Hz) 50 (60)
6 Horizontal busbar Rated current ≤ 5000A
7 Rated short-time withstand current (Icw) (kA) 50, 65, 80 (1s r.m.s.)
8 Rated peak withstand current (Ipk) (kA) 105, 140, 176 (0.1s maximum)
9 Vertical busbar Rated maximum operating current ≤ 1000A
10 Rated short-time withstand current 50kA
11 Rated peak withstand current 105kA
12 Enclosure protection degree IP30 IP40 (special note)

This switchgear introduces ABB (Switzerland) standard technology and has been technically improved on the basis of the original, making it better suited to China's national conditions. The cabinet body is assembled with connectors from C-section profiles with a 25 mm module, forming frame structures and drawer units that meet various requirements. High-strength flame-retardant engineering plastic components are used in the MCC cabinets, making them safer and more reliable. In addition, foreign functional boards have been remodeled and combined with a 200 mm module, which better meets the design requirements of mixed installation of PC cabinets and MCC cabinets. The draw-out units and the cabinet body have reliable interlocking devices to prevent the drawer from being pulled out under load when the switchgear is energized, which improves safety. In addition, the cabinet body is generally assembled from cold-rolled steel plate after passivation treatment, and aluminum-zinc coated steel plate can also be used according to different user needs.

I. Types of Switchgear
1. Incoming and Bus-tie Cabinets
Frame-type circuit breakers of various types from home and abroad, such as the RMW1, CW1, NA1, DW45, CDW7, MT, and E series, are used as the main switch to realize incoming power or bus-tie functions.
2. Power Center Cabinets (PC)
Frame-type circuit breakers of various types from home and abroad, such as the DW45, NA1, CDW7MT, and E series, are used for power distribution.
3. Motor Control Center (MCC)
Composed of drawers of different sizes. The main switch of each circuit adopts a high-breaking-capacity molded case circuit breaker or a rotary load switch with fuse.
4. Reactive Power Compensation Cabinets

II. Cabinet Introduction
1. Basic Cabinet Dimensions
Incoming and Bus-tie Cabinets

Unit Main Busbar Transfer Cabinet Incoming and Bus-tie Cabinet
Height (mm) 2200 2200
Width (mm) 400 600 800 1000
Depth (mm) 800 1000 800 1000
Remarks
100013 Power Center (PC) Cabinets
Unit 2 Circuit Breakers 3 Circuit Breakers
Height (mm) 2200 2200
Width (mm) 800 1000 800 1000
Depth (mm) 800 1000 800 1000
Remarks Similar circuit breakers with DW45-2000 and below load capacity and smaller volume Similar circuit breakers with DW45-2000 and below load capacity and smaller volume
Motor Control Center (MCC) Cabinets and Capacitor Compensation Cabinets
Unit MCC Cabinet Capacitor Compensation Cabinet
Height (mm) 2200 2200
Width (mm) 600 800 1000 600 800 1000
Depth (mm) 1000 800 1000 800 1000 800 600 800 1000 600
100004 Busbar Zone
Cable Zone
Apparatus Zone

About Us

XUBIAN ELECTRIC POWER YOU CAN TRUST

Wenzhou Xubian Electric Co., Ltd.
  • 10+

    Years Experience

Wenzhou Xubian Electric Co., Ltd. is a technology-driven China XBMNS Low voltage draw out switchgear Supplier and Custom XBMNS Low voltage draw out switchgear Factory, specializing in the production, sales and after-sales maintenance of high- and low-voltage complete switchgear systems.

We have a dynamic and innovative team for R&D, design, management and marketing, backed by solid R&D and production competence.

Following our quality policy: “Survival through Quality, Development through Innovation, Continuous Improvement, Customer Satisfaction”, we enforce strict control over all production stages to ensure 100% qualified finished goods. Our workshop is well‑equipped with full‑range processing facilities, testing apparatus and advanced inspection solutions.

View More
Wenzhou Xubian Electric Co., Ltd.

Company Philosophy

Quality Centered, Quality First, Win-Win Cooperation

Company Mission

To become a trusted global manufacturing partner for power transmission and distribution equipment.
  • Factory equipment
  • Factory equipment
  • Factory equipment
  • Factory equipment
  • Factory equipment
  • Factory equipment
  • Factory equipment
  • Factory equipment
  • Warehouse
  • Warehouse
News Center

Keep Up To Date With Our Latest News.

View More

Certificate Of Honor

  • 1
  • 2